TRUSTXCARE — Sharma Electrical and Electronics Logo
TRUSTXCARE
Sharma Electrical and Electronics
Get Quote
Active Workshop & Field Scope
Motor Engineering & Rewinding

Electric Motor Rewinding Services in Bihar

मोटर बाइंडिंग (कॉपर वायर वाइंडिंग)

Burnt windings and insulation breakdowns are common in Bihar due to voltage fluctuations and summer overheating. At Sharma Electrical and Electronics, we carry out motor rewinding using 100% genuine copper magnet wire, high-grade Nomex/Mylar insulation paper, precision coil winding data, and double varnish dipping with oven curing to ensure maximum lifespan.

Electric Motor Rewinding (Copper Coil Winding)
Active Workshop Service
PNB Chowk, Basaitha, Muzaffarpur (843101)
Electric Motor Rewinding (Copper Coil Winding) bench & field service coordinated from PNB Chowk, Basaitha, Muzaffarpur.
Typical Turnaround:24 to 48 hours
Brands Handled:
Kirloskar
Crompton
Havells
ABB
Texmo
Oswal
Falcon

Service Coverage & Operational Note

Core workshop specialty at PNB Chowk, Basaitha, Muzaffarpur; motors accepted from all North & Central Bihar districts.

हिंदी ग्राहक सहायता (Bihar Helpdesk)PNB चौक, बसैठा, मुजफ्फरपुर (843101)

100% प्योर कॉपर वायर मोटर बाइंडिंग (रिवाइंडिंग) वर्कशॉप

वोल्टेज उतार-चढ़ाव से जली मोटर की ओरिजिनल गेज कॉपर वायर, क्लास-F/H इंसुलेशन पेपर और डबल वार्निश बेकिंग के साथ टिकाऊ रिवाइंडिंग मुजफ्फरपुर में उपलब्ध है।

Problems Solved

  • Dead or shorted motor windings emitting burnt varnish smell
  • Repeated coil failures caused by substandard aluminum or thin-gauge local rewinds
  • Low insulation resistance from monsoon humidity

Warning Signs Requiring Immediate Inspection

If your motor, pump, or electrical panel exhibits any symptom below, isolate power immediately and consult our PNB Chowk, Basaitha workshop before severe coil or switchgear damage occurs:

  • Stator coil burnout due to low voltage
  • Turn-to-turn short circuits
  • Phase failure (single phasing) burnout in 3-phase motors
  • Moisture penetration causing insulation breakdown

Equipment Handled & Workshop Scope — Motor Rewinding

Detailed equipment categories, testing standards, and turnaround parameters.

CategoryEquipment & Assemblies HandledEngineering & Brand Notes
Equipment Scope 1Single & Three-Phase Induction StatorsSupported Makes: Kirloskar, Crompton, Havells, ABB, Texmo, Oswal, Falcon
Equipment Scope 2Flour Mill & Rice Mill Drive MotorsEstimated Turnaround: 24 to 48 hours
Equipment Scope 3Compressor & Chiller Blower MotorsPrecision pitch and turn count verification per manufacturer specifications
Equipment Scope 4Monoblock & Pump Drive StatorsStator core de-rusting, tooth cleaning, and slot liner replacement

Technical Capabilities & Specifications

  • Pure super-enameled electrolytic copper winding up to 25+ HP
  • Class-F and Class-H Nomex/Mylar insulation systems
  • Single-phase & 3-phase concentric/lap winding execution
  • Varnish impregnation and thermal moisture curing

Included Workshop Deliverables:

100% pure electrolytic copper wire rewinding to exact OEM wire gauges
Slot insulation with Class-F & Class-H thermal resistant insulating sheets
Precision pitch and turn count verification per manufacturer specifications
Stator core de-rusting, tooth cleaning, and slot liner replacement
Double varnish dipping and heat curing for vibration and moisture resistance
High-voltage insulation resistance testing (Megger) before reassembly

Service Boundaries & Honest Limitations

We believe in upfront technical honesty before accepting equipment or dispatching technicians across Bihar:

  • Burnt stator core laminations with severe welded iron hot-spots may be uneconomical to rewind and will be advised honestly during inspection
  • Aluminum-to-copper conversion requires careful slot space check
Need B2B or AMC? Explore our structured factory and commercial maintenance coverage on B2B Industrial AMC.

Standard Operating Procedure

Our 6-Step Engineering Execution Process

01

Winding Data Recording

Record exact coil pitch, turns per coil, wire SWG gauge, and star/delta grouping before stripping.

02

Clean Stripping & Slot Prep

Remove burnt coils without damaging stator laminations; de-rust teeth and fit fresh slot liners.

03

Copper Coil Insertion & Lacing

Wind pure enameled copper coils, insert phase separators, solder joints, and lace overhangs tightly.

04

Double Varnish & Heat Curing

Impregnate stator with insulating varnish and heat cure for moisture and vibration protection.

05

Megger Check & Amp Verification

Reassemble with checked bearings and test running current balance and insulation resistance.

06

Handover & Voltage Protection Guidance

Clear explanation of root cause, capacitor/relay/starter preventive advice, and transparent workshop invoice or job record.

Sector Applications

Industries Relying on Motor Rewinding

All 10 Industries
Workshop Authenticity & Capability Record

Physical Workshop Verification & Job Templates

Every diagnostic & rewinding assignment is anchored at our physical workshop at PNB Chowk, Basaitha, Muzaffarpur.

Workshop Capability Template (Pending Job-Sheet Photo)

Three-Phase Flour Mill (Atta Chakki) Induction Motor Copper Rewinding

3-Phase Squirrel Cage Induction Motor (TEFC) • 7.5 HP – 15 HP Range (Workshop Standard)

Typical Fault: Stator phase-to-phase insulation breakdown caused by sustained low-voltage supply drops and grain-dust accumulation around cooling fins.

Acceptance Check: Standard workshop acceptance check: winding phase balance, Megger insulation resistance check, and no-load running current verification prior to handover.

Workshop Capability Template (Pending Job-Sheet Photo)

Agricultural & Commercial Borewell Submersible Pump Rewinding & Bearing Overhaul

Water-Filled Borewell Submersible Pump Motor • 3 HP – 7.5 HP Range (Workshop Standard)

Typical Fault: Water ingress past worn mechanical/oil seals and thrust-bearing wear causing rotor drag, high amp draw, and burnt PVC-insulated submersible winding.

Acceptance Check: Standard workshop test-tank submersion continuity check, Megger insulation test, and rated current verification.

Direct Workshop Call

Speak with technician (Mon – Sat: 9:00 AM – 7:00 PM (Sunday Closed))

Call +91 83407 62551

Pre-Filled Quotation Form

Upload motor nameplate or BOQ for estimate

Request Quote

PNB Chowk, Basaitha HQ

Kamalpura, Muzaffarpur, Bihar 843101

Get Directions
Motor Rewinding FAQs

Frequently Asked Questions — Motor Rewinding

TRUSTXCARE • Sharma Electrical and Electronics

Ready for Reliable Motor Repair or Industrial Electrical Contracting?

Contact our Basaitha, Muzaffarpur engineering workshop today for transparent estimates, emergency support, and verified Bihar-wide dispatch.

Call Now
WhatsApp
Get Quote