TRUSTXCARE — Sharma Electrical and Electronics Logo
TRUSTXCARE
Sharma Electrical and Electronics
Get Quote
Active Workshop & Field Scope
Motor Engineering & Rewinding

Industrial 3-Phase Electric Motor Overhaul & Reconditioning

इंडस्ट्रियल 3-फेज मोटर ओवरहॉल एवं रीकंडीशनिंग

Heavy industrial motors suffer combined electrical insulation aging and mechanical wear on end-shields, shafts, cooling fans, and bearings. Our Industrial Motor Overhaul covers full stator cleaning, thermal varnish re-impregnation or full Class-H copper rewinding, precision bearing housing check, shaft alignment, cooling shroud restoration, and Megger/ampere test verification.

Industrial 3-Phase Motor Overhaul & Reconditioning
Active Workshop Service
PNB Chowk, Basaitha, Muzaffarpur (843101)
Industrial 3-Phase Motor Overhaul & Reconditioning bench & field service coordinated from PNB Chowk, Basaitha, Muzaffarpur.
Typical Turnaround:24 to 72 hours depending on HP & scope
Brands Handled:
ABB
Siemens
Crompton Greaves
Bharat Bijlee
Kirloskar
Havells
Marathon

Service Coverage & Operational Note

Executed at our Basaitha, Muzaffarpur workshop with pickup/drop coordination across Tirhut, Darbhanga, Patna, and Begusarai industrial clusters.

हिंदी ग्राहक सहायता (Bihar Helpdesk)PNB चौक, बसैठा, मुजफ्फरपुर (843101)

इंडस्ट्रियल 3-फेज मोटर ओवरहॉल एवं संपूर्ण रीकंडीशनिंग

फैक्ट्री, मिल और कोल्ड स्टोरेज की बड़ी 3-फेज मोटरों की पूरी जांच, बेयरिंग व शाफ्ट मरम्मत, थर्मल वार्निश ट्रीटमेंट, मेगर टेस्टिंग और क्लास-H कॉपर वाइंडिंग की विश्वसनीय सेवा।

Problems Solved

  • Repeated bearing seizures and shaft scoring under belt loads
  • Low insulation resistance causing earth-leakage breaker trips
  • High running temperature reducing motor service life

Warning Signs Requiring Immediate Inspection

If your motor, pump, or electrical panel exhibits any symptom below, isolate power immediately and consult our PNB Chowk, Basaitha workshop before severe coil or switchgear damage occurs:

  • Bearing raceway pitting and noisy rotor rub
  • Insulation resistance drop from moisture, oil, or mill dust
  • Broken cooling fan causing stator overheating
  • Burnt terminal studs and cracked terminal box

Equipment Handled & Workshop Scope — Industrial Overhaul

Detailed equipment categories, testing standards, and turnaround parameters.

CategoryEquipment & Assemblies HandledEngineering & Brand Notes
Equipment Scope 1TEFC 3-Phase Squirrel-Cage Induction MotorsSupported Makes: ABB, Siemens, Crompton Greaves, Bharat Bijlee, Kirloskar, Havells, Marathon
Equipment Scope 2Compressor & Chiller Drive MotorsEstimated Turnaround: 24 to 72 hours depending on HP & scope
Equipment Scope 3Industrial Blower & Exhaust MotorsClass-F/H electrolytic copper rewinding or varnish re-impregnation
Equipment Scope 4Mill Pulverizer & Conveyor MotorsEnd-shield bearing seat checking, shaft polishing & keyway inspection

Technical Capabilities & Specifications

  • Class-F (155°C) and Class-H (180°C) thermal insulation systems
  • Stator core cleaning and varnish baking for moisture recovery
  • 3-phase winding resistance balance and Megger IR validation
  • Drive-end & non-drive-end bearing extraction and alignment

Included Workshop Deliverables:

Complete teardown, stator core degreasing & slot inspection
Heavy-duty SKF/NBC bearing replacement & thermal grease packing
Class-F/H electrolytic copper rewinding or varnish re-impregnation
End-shield bearing seat checking, shaft polishing & keyway inspection
Cooling fan blade & cowl restoration to prevent thermal buildup
1000V Megger insulation check and balanced 3-phase no-load run testing

Service Boundaries & Honest Limitations

We believe in upfront technical honesty before accepting equipment or dispatching technicians across Bihar:

  • High-tension (HT 3.3kV/6.6kV/11kV) motors and motors above workshop crane/weight capacity require prior technical qualification
  • Sub-surface crack welding on cast-iron frames is evaluated case-by-case
Need B2B or AMC? Explore our structured factory and commercial maintenance coverage on B2B Industrial AMC.

Standard Operating Procedure

Our 6-Step Engineering Execution Process

01

Incoming Electrical & Mechanical Audit

Record nameplate specs, winding resistance, Megger IR value, and rotor shaft play before teardown.

02

Dismantling & Chemical Cleaning

Disassemble end-shields, pull worn bearings, and clear carbon, oil, and husk dust from core ducts.

03

Winding Restoration / Rewind

Either oven-dry & re-varnish healthy coils or perform precision Class-F/H copper rewinding.

04

Mechanical & Bearing Assembly

Install genuine heavy-duty bearings, pack high-temp grease, and verify smooth rotor spin.

05

Final Megger & Trial Run

Verify balanced 3-phase no-load current, temperature rise, and vibration before dispatch.

06

Handover & Voltage Protection Guidance

Clear explanation of root cause, capacitor/relay/starter preventive advice, and transparent workshop invoice or job record.

Sector Applications

Industries Relying on Industrial Overhaul

All 10 Industries
Workshop Authenticity & Capability Record

Physical Workshop Verification & Job Templates

Every diagnostic & rewinding assignment is anchored at our physical workshop at PNB Chowk, Basaitha, Muzaffarpur.

Workshop Capability Template (Pending Job-Sheet Photo)

Three-Phase Flour Mill (Atta Chakki) Induction Motor Copper Rewinding

3-Phase Squirrel Cage Induction Motor (TEFC) • 7.5 HP – 15 HP Range (Workshop Standard)

Typical Fault: Stator phase-to-phase insulation breakdown caused by sustained low-voltage supply drops and grain-dust accumulation around cooling fins.

Acceptance Check: Standard workshop acceptance check: winding phase balance, Megger insulation resistance check, and no-load running current verification prior to handover.

Workshop Capability Template (Pending Job-Sheet Photo)

Rice Mill Drive & Paddy Cleaner Motor Bearing & Insulation Overhaul

3-Phase Totally Enclosed Fan-Cooled (TEFC) Mill Drive Motor • 10 HP – 25 HP Range

Typical Fault: Excessive vibration and rotor-to-stator rubbing risk caused by seized drive-end bearing housing and husk/dust clogging cooling air ducts.

Acceptance Check: Standard overhaul sign-off: smooth bearing acoustics, balanced 3-phase current draw, and verified insulation resistance.

Direct Workshop Call

Speak with technician (Mon – Sat: 9:00 AM – 7:00 PM (Sunday Closed))

Call +91 83407 62551

Pre-Filled Quotation Form

Upload motor nameplate or BOQ for estimate

Request Quote

PNB Chowk, Basaitha HQ

Kamalpura, Muzaffarpur, Bihar 843101

Get Directions
Industrial Overhaul FAQs

Frequently Asked Questions — Industrial Overhaul

TRUSTXCARE • Sharma Electrical and Electronics

Ready for Reliable Motor Repair or Industrial Electrical Contracting?

Contact our Basaitha, Muzaffarpur engineering workshop today for transparent estimates, emergency support, and verified Bihar-wide dispatch.

Call Now
WhatsApp
Get Quote